Ovens

html

Serv ice Quick Guid e

SQG_CK_39_EN

Indesit Company, Service Department

HOTTIMA 2010 (Full) Fault Table

FAULT SUBCODE DESCRIPTION CHECK S

F01

01 Main PCB probe short circuited.

1 Unplug, wait for 2 minutes, plug

back in again and test the appli-

ance.

2 Replace the main PCB.

02 Main PCB probe circuit open.

11h Rtn out of range

12h Vline out of range

21h No mains voltage / Master Relay Fans open

22h Mains voltage present / Master Relay Fans

shortcircuited /(Fan triac short circuited).

51h Floor heating element circuit: Triac open or

relay not closing

52h Circular heating element circuit : Triac open

or relay not c losing

54h Steam heating element circuit: Triac open or

relay not closing

56h Grill 1 heating element circuit: Triac open or

rela y not closing

57h Grill 2 top heating element circuit: Triac

open or relay not closing

58h Divider heating element circuit: Triac open

or rela y not c losing

59h Ceiling heating element circuit: Triac open

or rela y not c losing

61h Floor heating element feedback failure

62h Circular heating element feedback failure

63h Steam heating element feedback failure

64h Grill 1 heating element feedback failure

65h Grill 2 heating element feedback failure

66h Divider heating element feedback failure

67h Ceiling heating element feedback failure

90h DS / Divider circuit (analogue inputs)

out of range

F02

1 Visual Board probe short circuited. 1 Unplug, wait for 2 minutes, plug

back in again and test the appli-

ance.

2 Replace the Display PCB.

3 Replace the Main PCB.

2 Visual Board probe circuit open

21h uP1 – uP2 communication

31h Display keys

F03*

1 Visual board setting 1 Check the PTC probe in the

main cavity (lower) is working

properly.

2 Check connectors on the board

and component sides.

3 Check the state of cables.

4 Replace the Main PCB.

01 Main oven probe short circuited.

02 Main oven probe circuit open.

* N.B: Open Space appliances only.

1/4

HOTTIMA 2010 (Full) Fault Table

FAULT SUBCODE DESCRIPTION CHECK S

05 No gradient for main oven probe. 1 Check the PTC probe in the top cavity is

working

properly.

01 Top oven probe short circuited.

2 Check connectors on the board and

component

F53** 02 Top oven probe circuit open. sides.

3 Check the state of cables.

05 No gradient for top oven probe. 4 Replace the main PCB.

1 Check installation of appliance (ventilation)

2 Check that the tangential fan is working properly.

F4 01 Main PCB probe temperature

too high.

3 Check connectors on component and

board sides.

4 Check the state of cables.

5 Replace the Main PCB.

1 Check installation of appliance (ventilation)

2 Check that the tangential fan is working properly.

F5 01 Visual PCB probe temperature

too high.

3 Check connectors on component and

board sides.

4 Check the state of cables.

5 Replace the Main PCB.

F6 01 Temperature too high in the Main/

Top cavity.

1 Check PTC probe is configured properly.

2 Replace the Main PCB.

01 Door Lock – NO LOCK 1 Check the door lock is working properly.

02 Door Lock – NO UNLOCK 2 Check connectors on component and board

F7 03 Door Lock – FB BROKEN sides.

3 Check the state of cables.

D o o r l o c k – T R I A C S H O R

T CIRCUITED (BP BISTABLE)

4 Replace the Main PCB.

1 Check that the pin probe hasn't short circuited.

2 Check connectors on component and board

F8 01 Food probe short circuited (pin) sides.

3 Check the state of cables.

4 Replace the Main PCB.

01h Setting File / DataReady MAIN 1 Unplug, wait for 2 minutes, plug back in again

and test the appliance.

F9 02h Setting File / DataReady VISUAL

2 Reprogram the Main PCB.

03h

Setting File / DataReady NOT DATA

READY

3 Replace the Main PCB.

4 Replace the Display PCB.

01 Temperature Selector short circuited 1 Check connectors on component and

board sides.

F10

2 Check the state of cables.

02 Temperature Selector circuit open. 3 Replace temperature selector.

4 Replace the Main PCB.

** N.B: If the temperature measured by the PTC is below 0°C, the oven door will be blocked and

Fault “F53” will appear.

2 / 4

HOTTIMA 2010 (Full) Fault Table

FAULT SUBCODE DESCRIPTION CHECK S

F12

01 Communication- MAIN

1 Unplug, wait for 2 minutes, plug back in again and

test the appliance.

2 Reprogram the Main PCB.

3 Replace the Main PCB.

4 Replace the Display PCB.

02 Communication - VISUAL

C o m m u n i c a t i o n - N O

A L I G N M E N T W I T H M A I N

SETTING (ON BOARD SETTING

OK (CHKSUM OK))

C o m m u n i c a t i o n - N O

A L I G N M E N T W I T H M A I N

SETTING + ON BOARD SETTING

CORRUPTED (CHKSUM KO))

F13 01

F l o o r h e a t i n g e l e m e n t : D I

S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the floor heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F14 01

Circular heating element D

I S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the circular heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F16 01

S t e a m h e a t i n g e l e m e n t : D I

S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the steam heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F17 01

G r i l l 1 h e a t i n g e l e m e n t : D I

S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the Grill 1 heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F18 01

Grill 2 heating element: D

I S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the Grill 2 heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F19 01

Divider heating element: D

I S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the divider heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F20 01

Ceiling heating element: D

I S C O N N E C T E D o r

INTERRUPTED / heating element

relay jammed / heating element

dispersing energy, master relay

jammed.

1 Check that the ceiling heating element is working

properly.

2 Check connectors on component and board sides.

3 Check the state of cables.

4 Replace the Main PCB.

F22 01

A heating element is dispersing

energy (not possible to indicate

which) or master relay jammed.

1 Check if any of the heating elements are

dispersing

energy.

2 Replace the Main PCB.

3 / 4

HOTTIMA 2010 (Full) Fault Table

FAULT SUBCODE DESCRIPTION CHECK S

F24

P25

71h Tangential fan in diode mode. 1 Check that the tangential fan is working

properly.

2 Check that the motor fan is working properly.

3 Checkconnectors on componentand

main PCB sides.

4 Check the state of cables on both fans.

5 Replace the Main PCB.

Replace the ACU

72h Tangential fan short circuited or

disconnected.

73h Tangential fan circuit open.

74h Tangential fan FB failure.

75h Tangential fan general failure.

76h Tangential fan in diode mode +

master relay jammed.

81h Circular fan in diode mode.

82h Circular fan short circuited or

dis-connected.

83h Circular fan circuit open.

84h Circular fan FB failure.

85h Circular fan general failure.

86h

-------

Circular fan in diode mode + master

relay jammed.

Maximum Number of Master Relay

Switch Under Load Reached

F27

01 Function selector short circuited.

1 Check connectors on component and

board sides.

2 Check the state of cables.

3 Replace function selector.

4 Replace the Main PCB.

02 Function selector circuit open.

Faults Heating table: Elements Legend:

1) Circular heating element 5) Ceiling heating element

2.Grill 1 6) Floor heating element

3.Grill 2

4.Divider heating element

2 3

Standard Oven Open Space Oven Double Oven

4/4

5 3

Created with the Personal Edition of HelpNDoc: Create cross-platform Qt Help files